11/29/2023 0 Comments Balena etcher clone drive![]() And I understand Igor's opinion that it's much more useful to save /home/* and /etc/* and a list of installed packages, but I want to have a working clone handy for instant use in case the #1 SD card fails, mostly because I am planning on installing pihole and I am worried about increased wear on the SD card. I don't want to (can't) use dd because the SD card #3 is only 16 GB, whereas the #1 SD card is 32 GB, and my armbian installation takes only 4,1 GB. This is a mouse-driven application, which requires you to first select the partition you need to clone.Update: I tried to clone the SD card doing the following, inspiration from this thread:ġ) download armbian image, burn to another SD card (#2)Ģ) run armbian from this SD card #2 (works)ģ) insert former boot SD card (#1) and backup SD card (#3) in SD card readerĤ) dd if=/dev/#1 of=/dev/#3 bs=1M count=4 (to copy partition scheme and bootloader)ĥ) mount #1 /mnt/origin, mount #3 /mnt/cloneĦ) rsync -avSz /mnt/origin /mnt/clone (seems to work)ħ) check /etc/fstab on #3, adjust UUID of /Ĩ) try to boot from #3 -> doesn't work :-( ![]() This has been fixed, and the faulty releases have been pulled. Launch from the command line with: sudo partimage Etcher on Windows v1.5.107, 1.5.108, 1.5.109 and, 1.5.110 has a bug in the clone drive feature that erases the partition table of the source disk. To install the Partimage disk clone software on Ubuntu: sudo apt install partimage You can exit Partimage at any time with the F6 key. Otherwise, you'll need to exit Partimage to do so before continuing with the process. You can use it to clone the Linux filesystem ext3, as well as Windows disk formats (FAT32 or NTFS).īefore starting, ensure that the partition you wish to clone is unmounted. It is also called balenaEtcher since it is developed by balena. However, Partimage does not support the ext4 filesystem, so avoid using it for cloning disks or partitions of that type. It protects a user from accidentally overwriting hard-drives by making drive selection obvious and with validated flashing there is no more writing images to corrupted drives. This simple and intuitive free tool can also be used to. NOTE: These installation methods only work. ![]() Partimage is also available for most distros, and doesn't carry any "disk destroyer" risks! You can easily write an ISO to USB or clone USB drives by using the Balena Etcher software utility. Following are instructions on how to setup GParted Live on your USB flash drive using either MS Windows or GNU/Linux. Clonezilla claims to be a similar software solution to what Acronis True Image and other programs offered a disk imaging/cloning program with unimpressive. If you find dd too complicated, Partimage is a good alternative to clone Linux drives. Just be certain that the destination volume is large enough!Ģ. You can even use this command to clone a disk to a larger drive. Having been configured in a RPI2 - idea to duplicate the card for several other RPIs wanting the same. Drive image was of LibreELEC-RPi2.arm-9.2.6.img.gz written to a sandisk 8Gb Ultra uSD card. It failed with a read error, looked to have corrupted the drive but unplug and replug and all was still ok. How long it takes to clone the Linux drive will depend on the size of the disk or partition. So to be fair i have now tried imaging the drive with Rufus, and it also had issues. This might be a secondary, or external, disk drive attached to your computer. If you only want to clone a partition of your Linux disk drive, use: dd if=/dev/sda1 of=/dev/sdb1 bs=64K conv=noerror,syncĪs you can see, dd will clone partition sda1 (partition 1 on device sda) to sdb1, a newly created partition 1 on device sdb. However: while a larger block size makes transfer quicker, a smaller block size makes the transfer more reliable. It's best to include 64K or the larger 128K as a condition. Let's break this command down for clarity:Ībout the 64K settings, the default value is 512 bytes, which is rather small. ![]() To clone your computer's hard disk, use the command: dd if=/dev/sdX of=/dev/sdY bs=64K conv=noerror,sync You'll find dd built into most Linux operating systems-if not, install it from the package manager.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |